认证业务
 
童车、婴儿床安全标准检测
 

童车、婴儿床安全标准检测

日期:2016-7-29 16:39:54 人气:2182
随着生活水平的提高,童车童床的市场需求越来越大。由于这类产品主要面对的是行为能力较低的婴幼儿,因此其安全性备受关注。许多国家针对这类产品的使用性质进行了分类,并且制定了具有针对性的标准进行安全管控。
With the improvement of living standards, the crib stroller market demand is growing.Because these products are for lower capacity infants, its security was concerned. For many countries, the use of the nature of these products are classified, and to develop a standard for secure targeted control.

美国—ASTM F406
该标准适用于非全尺寸童床和游戏围栏。这类产品设计给身高小于35 in.(890 mm)的儿童玩耍和睡觉使用。
This standard applies to non-full-size cribs and playpens. These products designedfor height less than 35 in. (890 mm) for children to play and going to bed.
1.1角柱Prism
1.2尖点、利边、小部件、木材上的毛刺和木屑 Sharp points, small sharp edges, parts, burr wood and sawdust
1.3剪夹点Scissors grips                   1.4玩具 Toy
1.5锁定机构 Locking Mechanisms          1.6开孔 Openings
1.7保护件 Protective Components          1.8标签 labeling
1.9稳定性 Stability                        1.10绳子和带子的长度 Length of rope and tape
1.11弹簧 Coil Springs                     1.12附件里的陷入间隙 Entrapment in Attachments
1.13床垫 Mattress                        1.14突出物 Protrusions
1.15硬质材料围栏的性能要求 Performance Requirements for Rigid Sided Products
1.16网状或者纺织品围栏的性能要求 Performance Requirements for Mesh/Fabric Products
1.17标志和标签 Marking and labeling      1.18说明材料 Instructions

英国—BS EN 716
该标准适用于在室内使用的内部长度大于900mm但不大于1400mm的童床。
The standard applies to indoor use internal length greater than 900mm and not more than 1400mm of the crib.
 
标准检测
1. 安全要求       Safety requirements     
1.1边和突出物    Edges and protruding parts    1.2自攻螺丝      Self-tapping screws
1.3标签和贴花纸  Labels and decals            1.4小物件        Small parts
1.5脚轮和车轮    Castors and wheels
1.6床边的孔、缝隙和开口Holes, gaps and openings on the inside of the cot
1.7童床外侧的可能夹住头部的结构Head entrapment on the outside of the cot
1.8剪夹点Shear and squeeze points            1.9支撑点Snag points
1.10 锁定系统Locking systems                 1.11 床底Cot base
1.12 侧面和端部Sides and ends                1.13 床边框Cot rim
1.14 稳定性Stability                           1.15 床垫尺寸Mattress size

1.16 包装Packaging                           1.17 使用说明Instructions for use


中国GB 14747
该标准适用于供一名儿童或者多名儿童乘坐的儿童三轮车。
This standard applies to tricycles for a child or more children.
1.1材料 Material     1.2机械强度 Mechanical strength
1.3锐利边缘、锐利尖端、外露突出物、挤夹点和小零件 Sharp edges,
sharp tip, exposed protrusions, pinch points and small parts
1.4稳定性 Stability      1.5零件 Parts
1.6产品标志和使用说明 Product Marking and instructions

中国—GB 14749
该标准适用于从能够坐立到能够自己行走的婴儿使用的婴儿学步车。
This Standard specifies safety requirements for baby walking frames into which a child is placed, and intended to be used from when the child is able to sit up by itself until the child is able to walk by itself.
1.1材料 Material       1.2金属表面防腐蚀 Corrosion of metal surfaces
1.3结构 Structure      1.4静态和动态稳定性 Static and dynamic stability
1.5静态和动态强度 Static and dynamic strength
1.6用于包装或学步车上的塑料袋或塑料薄膜 Plastic bags or plastic film for packaging or on a baby walking frames
1.7标志和使用说明 Signs and instructions

中国—GB 14748
该标准适用于供一名儿童或者多名儿童乘坐的儿童轮式推车。
This standard applies to wheeled child conveyances for a child or more children.
1.1材料 Material    1.2金属表面防腐蚀 Corrosion of metal surfaces
1.3结构 Structure   1.4基本尺寸 Basic dimensions
1.5推车适用年龄 Carts for age
1.6卧兜和座兜连接在车架上的装置 devices for pram bodies and seat units mechanism connected on the frame
1.7稳定性 Stability   1.8手柄强度 Grip strength
1.9制动装置 Brake
1.10折叠机构锁定装置 Folding mechanism locking device
1.11可拆卸卧兜或座兜的连接装置的强度和耐用性 Strength and durability of attachment devices for pram bodies or seat units
1.12束缚系统 Restraint system
1.13车轮的强度 The strength of the wheel
1.14动态耐久性测试 Dynamic endurance testing
1.15撞击强度 Impact strength
1.16静态强度 Static strength
1.17塑料包装袋和软塑料薄膜 Plastic bags and soft plastic film
1.18产品标志和使用说明 Product Marking and instructions

欧盟—EN 1273/BS EN1273
该标准适用于从能够坐立到能够自己行走的婴儿使用的婴儿学步车。
This Standard specifies safety requirements for baby walking frames into which a child is placed, and intended to be used from when the child is able to sit up by itself until the child is able to walk by itself.
1.1开孔 Openings
1.2边、角和突出物 Edges, corners and projections
1.3小物件 Small parts                   1.4贴花纸 Decals
1.5绳、带和用于绑的部件 Cords, ribbons and parts used as ties
1.6硬质的活动部件 Rigid moving parts     1.7座椅 Seat
1.8折叠机构和框架的调整装置 Folding and frame adjustment mechanisms
1.9静态稳定性 Static stability
1.10防止跌落台阶的保护装置 Prevention of falls down steps
1.11动态稳定性 Dynamic stability          1.12强度 Strength
1.13停车装置 Parking devices
1.14贴花纸和标签的耐久性 Durability of decals and marking
1.15产品信息材料 Product Information Material   1.16包装 Package

欧盟—EN 1888
该标准适用于供一名儿童或者多名儿童乘坐的儿童轮式推车。
This standard applies to wheeled child conveyances for a child or more children.
1.1结构 Structure                      1.2稳定性 Stability
1.3可换向的推车 Reversible carts        1.4手柄 Handle
1.5停车装置和刹车装置 Parking and braking devices
1.6折叠机构的锁定装置 Locking devices for the folding mechanism
1.7有提手的卧兜的纵向稳定性
Longitudinal stability of a pram body with carrying handles

1.8提手/手柄与卧兜/可拆卸的座兜的连接点 Carrying handles and handle anchorage points of pram bodies and detachable seat units
1.9可拆卸卧兜或座兜的连接装置的强度和耐用性 Strength and durability of attachment devices for pram bodies or seat units
1.10束缚系统 Restraint system      1.11车轮强度 Wheels strength
1.12不规则表面测试 Irregular surface testing
1.13标签的耐久性 Label durability    1.14塑胶包装 Plastic Packaging
1.15产品信息 Product Information
                                                 
美国—CPSC 16CFR 1220

该标准适用于在家内外、旅行和其它情况下使用的设计供婴儿睡觉的非全
尺寸童床。
The standard applies to both inside and outside the home, travel and other cases under the design used for non-full-size baby crib to sleep.
1.1尺寸 Size             1.2床边围栏高度 Bedside fence height
1.3部件间隙 Parts gap    1.4硬质部件 Rigid member
1.5结构和成品 Structure and finished   1.6床垫 Mattress
1.7组装说明 Assembly instructions
1.8可鉴定标志、警告语和符合声明
Identified signs, warnings and Compliance Statement
1.9记录保存 Record Keeping    
1.10不规则间隙要求 Irregular clearance requirements

美国—ASTM F1169
该标准适用于在家里使用的设计供婴儿睡觉的全尺寸童床。This standard applies to the design used in the home for a full-size baby crib to sleep.
1.1木材上的毛刺和木屑 Burr and sawdust on wood
1.2部件间隙 Parts gap     1.3硬质部件 Rigid member
1.4结构和成品 Structure and finished   1.5组装说明 Assembly instructions
1.6可鉴定标志、警告语和符合声明
Identified signs, warnings and Compliance Statement
1.7记录保存 Record Keeping  
1.8不规则间隙要求 Irregular clearance requirements

美国—ASTM F977
该标准适用于婴儿使用的婴儿学步车。This standard applies to Infant Walkers.
1.1锁定装置 Latching or Locking Mechanisms        1.2孔洞 Holes
1.3剪夹点 Scissoring, Shearing, Pinching            1.4外露弹簧 Exposed Coil Springs
1.5保护件 Protective Components                   1.6附属玩具 Subsidiary toys
1.7稳定性 Stability                                 1.8结构完整性 Structural Integrity       
1.9防止跌落台阶的保护装置 Steps to prevent the fall protection device
1.10标志和标签 Marking and labeling                1.11说明书 Instructions

美国—ASTM F833
该标准适用于供运载婴儿或者儿童的轮式推车。
This standard applies to wheeled carts for the carriage of infants or children.
1.1尖点、利边、小部件、木材上的毛刺和木屑 Sharp points, sharp
edges, small parts, burr wood and sawdust
1.2锁定装置 Latching Mechanisms                1.3开孔 Opening
1.4剪夹点 Scissors grips                         1.5外露弹簧 Exposed Coil Springs
1.6标签 labeling                                 1.7保护件 Protective Components
1.8座椅靠背角度测量 Seat Recline Measurement    1.9刹车装置 Brakes
1.10玩具 Toy                                   1.11静态载重 Static load
1.12稳定性 Stability                              1.13束缚系统 Restraint system
1.14乘座空间防护 Ride space protection
1.15汽车座椅和推车的结合组态 Car seat and stroller combination configuration
1.16撞击测试 Crash Testing
1.17可通过身体或者脚的开口 Through the opening of the body and the foot
1.18标志和标签 Marking and labeling
1.19说明材料 Instructions

欧盟—EN 1130
该标准适用于在室内使用的内部长度不大于900mm的童床和摇篮。
这种童床和摇篮是提供给婴儿睡觉时使用的,直到婴儿可以自行坐起、跪起或者用手撑起。
The standard applies to indoor use internal length of not more than 900mm of cribs and cradles. This crib and cradle is provided for use when the baby to sleep until the baby can sit up on their own, or by hand propped up from kneeling.
1.安全要求 Safety requirements     1.1材料 Material
1.2结构 Construction               1.3床底 Bed base
1.4侧面和端部 Sides and ends       1.5稳定性 Stability
1.6包装 Packaging                1.7使用说明 Instructions for use
1.8标志 Marking
2.测试方法 Test methods

澳大利亚/新西兰—AS/NZS 2088
该标准适用于供运载婴儿或者儿童的轮式推车。
This standard applies to wheeled carts for the carriage of infants or children.
1.1尺寸 Size                          1.2材料 Material
1.3与儿童头部接触的部件 Parts in contact with the child's head
1.4管端开口 Tube end opening          1.5可换向的手柄 Reversible handle
1.6放脚部件 Put the foot member        1.7可拆卸部件 Detachable parts
1.8停车装置 Parking device             1.9锁定装置 Locking device
1.10乘座空间防护 Ride space protection  1.11座位和靠背表面 Seat and backrest surface
1.12耐久性 Durability                   1.13突出物 Prominence
1.14危险利边 Dangerous sharp edges    1.15危险尖端 Dangerous tip
1.16稳定性 Stability                     1.17车轮的安全性 Safety wheel
1.18可换向手柄衔接点的安全性 Convergence point can be changed to handle security
1.19锁定装置的安全性 Locking security device
1.20包装和信息标签 Packaging and labeling information        1.21标志 Sign

美国—CPSC 16CFR 1219
该标准适用于供婴儿使用的全尺寸童床。The standard applies for the use of full-size baby crib.
1.1尺寸 Size                 1.2部件间隙 Parts gap
1.3硬质部件Rigid member     1.4结构和成品 Structure and finished
1.5组装说明 Assembly instructions
1.6可鉴定标志、警告语和符合声明 Identified signs, warnings and Compliance Statement
1.7记录保存 Record Keeping   1.8不规则间隙要求 Irregular clearance requirements

美国—ASTM F1821
该标准适用于供15个月以下体重不超过50 lb (27.7 kg)的儿童使用的,并且能够使用全尺寸童床床垫的婴儿床。
The standard applies for 15 months or less weighing less than 50 lb(27.7 kg) of the children, and be able to use the full-size crib mattress crib.
1.1尖点、利边、小部件、木材上的毛刺和木屑 Sharp points, sharp edges, small parts, burr wood and sawdust
1.2剪夹点 Scissors grips     1.3保护件 Protective Components
1.4开口 Opening            1.5标签 labeling
1.6角柱外延 Prism epitaxy   1.7床垫保留 Mattress reserved
1.8床垫支撑系统 Mattress support system
1.9与框架末端相连接的床垫支撑系统 The mattress supporting system connected to the end of the frame
1.10护栏 Fence            1.11框架末端 Frame ends
1.13标志和标签 Marking and labeling       1.14说明材料 Instructions


美国—ASTM F2194
该标准适用于供婴儿使用的摇篮。这类摇篮通常是由自由的腿、有轮的底部、可摇摆的底部或者可以摆动的底部支撑起一个稳固的底面。
1.1尖点、1.1利边、小部件、木材上的毛刺和木屑
Sharp points, sharp edges, small parts, burr wood and sawdust
1.2剪夹点Scissors grips            1.3意外折叠 Folding accident
1.4开孔 Opening                   1.5标签 labeling
1.6紧固件 Fastener                1.7角柱 Prism
1.8玩具 Toy                       1.9摇篮硬质围栏的空隙 Cradle rigid fence gap
1.10摇篮网状或者纺织品围栏的开口 Cradle mesh or textile fence openings
1.11静态负载 Static load             1.12稳定性 Stability
1.13床褥 Mattress                   1.14保护件 Protective Components
1.15标志和标签 Marking and labeling   1.16说明材料Instructions

下一个:金属材料测试
 
 
Copyright © 昆山北测检测技术有限公司 技术支持:昆山艾玛科技